A Beginner's Guide to Installing a Bathtub
A Beginner's Guide to Installing a Bathtub
Blog Article
This post in the next paragraphs on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is extremely informative. Check it out for your own benefit and see what you think about it.
Mounting a tub isn't precisely rocket science, yet it does require strong plumbing, woodworking, and often, tiling abilities. Changing an old bathtub with a brand-new one is also a moderately tough project. If the old tub is conveniently available, the task can move easily; if you need to open up a wall surface to eliminate the old tub and position the new tub, the task is a lot harder. In either instance, the task is within a house handyman's skills, although you will certainly require an assistant to vacate the old tub as well as set in the brand-new one. Make sure you have actually certified on your own for the task and also fit attempting it. Instead of hiring a contractor to take over a halfway-completed project, it is better to take into consideration employing one prior to you begin. Possibilities are you might require a specialist plumber to make tube links.
This article will certainly help you install a brand-new bath tub in your washroom if you have already purchased a brand-new bathtub and do not require to change the plan of your previous water system pipelines.
Your devices and also material list should comprise the following:
Removing Old Touches
If you require to replace old taps with new ones as a part of your installment, then the first thing you need to do is disconnect the supply of water. After doing so, switch on the taps to drain pipes any kind of water remaining in the system. The procedure of getting rid of the existing faucets can be rather problematic as a result of the restricted gain access to that is typically the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a cloth prepared for the remaining water that will originate from the pipes. As soon as the supply pipelines have actually been gotten rid of, make use of the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from turning during this procedure. Once the taps have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any type of old sealing compound.
Before carrying on to fit the brand-new faucets, compare the pipeline connections on the old taps to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will certainly require a plastic adapter to avoid damages to the thread. One end of the adapter fits on the plastic tail of the faucet and also the various other end provides a connection to the current supply pipes.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which attaches the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the faucet in the installing opening in the bath/basin ensuring that the washing machines are in area between the tap and also the sink. Secure the tap in position with the supplier supplied backnut. When the tap is securely in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by using corrugated copper piping or with regular tap ports. The previous kind ought to be linked to the tap ends first, tightening only by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Installing the Tub
Making use of both wood boards under its feet, place the bath tub in the required setting. The wooden boards are handy in uniformly spreading out the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto 4 small factors.
The next goal is to make sure that the bath tub is leveled all round. This can be accomplished by checking the level as well as readjusting the feet on the bath tub till the level reviews degree.
To install faucets, fit all-time low of the outermost adaptable faucet adapter to the suitable supply pipeline by making a compression sign up with; then do the very same for the various other faucet.
Activate the supply of water and examine all joints and also new pipework for leaks as well as tighten them if essential. Fill the tub and likewise examine the overflow outlet and the regular electrical outlet for leakages.
Ultimately, deal with the bath paneling as described in the maker's instruction manual. Tiling as well as sealing around the bath tub needs to wait until the bathtub has been made use of a minimum of once as this will settle it into its last placement.
Preparing for the Setup
First of all, the supporting structure provided with the bath ought to be fitted (if required) according to the manufacturer's directions. Next, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is very important to make sure that if the tap features a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is likewise sensible to fit a supporting plate under the taps device to stop stress on the tub.
Fit the adaptable faucet ports to the bottom of both faucets using 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet via the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make sure you make use of all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom should now prepare to be suited its last placement.
Tiling Around the Bathtub
In the area where the bath fulfills the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is important as the fitting can move enough to crack a rigid seal, causing the water to permeate the wall between the bath and the tiling, resulting in problems with dampness and feasible leakages to the ceiling below.
You can pick from a selection of coloured sealers to blend in your components and also fittings. They are sold in tubes and also cartridges, as well as are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger void to fill up, you can load it with twists of drenched newspaper or soft rope. Remember to always load the tub with water prior to sealing, to permit the movement experienced when the bathtub remains in use. The sealer can crack relatively very early if you do not take into consideration this activity before sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise quickly readily available on the marketplace. It is advisable to fit the ceramic tiles utilizing waterproof or water resistant sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a fervent reader on Tools You Need to Install a New Bathtub , I thought sharing that information was worthwhile. If you please take the time to share this blog post if you liked it. Bless you for your time. Don't forget to pay a visit to our blog back soon.
Facing a flood? Call us! Report this page